[HELP] DFI UT-X48 T2R 4E Error Code

[57.Christ]

Tweet

misii gan..

sesuai judul threadnya..g ada code error yang aneh neh..g uda baca di pdfnya..dia bilang kek gini:

4E

Test Base and Extended Memory
Test base memory from 256K to 640K and extended memory above 1MB using
various patterns.

NOTE: This test is skipped in EISA
mode and can be skipped with ESC key
in ISA mode.

ada yang bsa bantu g gak?
code error ini muncul klo g setting fsb di 430++ ( termasuk 430 )..padahal Vcore dah g set di 1,45, VTT 1,3 and V Nb di 1,45, tp tetep ogah jalan lebih dari 425..

thx buat bantuan para chipper..huhuhu, gak bsa OC ampe tinggi neh..

( FYI, sebelumnya juga pernah ada code2 error laen yang aneh2 juga, tp g lupa apa aja code2nya )

[roedzzz]

Tweet

Pake bios versi brapa bro?
Trus Divider strab memoru yg dipake yg mana?
Klo bisa posting secara detail sistem sama setingan biosnya..
Saya akan coba bantu semampu saya

[57.Christ]

Tweet

Pake bios versi brapa bro?
Trus Divider strab memoru yg dipake yg mana?
Klo bisa posting secara detail sistem sama setingan biosnya..
Saya akan coba bantu semampu saya

maap kelupaan posting boss..

bios yang versi terbaru dari webnya DFI 10-02-2008 ( maap lupa codenya )

divider di 333/800

td g uda sempet nyoba lagi bro:
VCore kebaca diBIOS 1,42 ( g set di 1,375 klo gak sala )
VTT kebaca 1,36
V NB kebaca 1,51

FSB 445 dia mo ngeboot, tp FSB 450 dia uda muncul kode 4E lagi..
sempet wkt itu pas lagi naekin FSB muncul kode 5d..ram g kedetect DDR2 2400..

kra2 masalahnya apa ya bro?

settingan diatas dah cukup lom? coz sisa settingan dram g set didefault ( 5-5-5-15 ) trus SB core, GTL ref, boot up clock g set didefaultnya semua..

[roedzzz]

Tweet

Setingan di atas sudah cukup saya rasa..
Kemungkinan besar masalahnya ada pada procie dan seting memori anda..
Kemungkinan procie anda tidak kuat jalan di fsb 430++ karna kekurangan vcore saya pikir
Coba setingan seperti ini..

CPU Feature Page
Thermal Management Control................Disabled
PPM (EIST) Mode...........................Disabled
Limit CPUID MaxVal........................Disabled
CIE Function..............................Disabled
Execute Disable Bit.......................Disabled
Virtualization Technology.................Disabled
Core Multi-Processing.....................Enabled

Main BIOS Page
Exist Setup Shutdown......................Mode 2
Shutdown after AC loss....................Disabled
O.C. Fail Retry Counter...................0
CPU Clock Ratio........................... default
CPU N/2 Ratio.............................Disabled
CPU Clock.................................430 MHz
Boot Up Clock.............................Auto
CPU Clock Amplitude.......................900mV
CPU Clock0 Skew...........................200ps
CPU Clock0 Skew...........................  0ps
DRAM Speed................................333/800
PCIE Clock................................100MHz
PCIE Slot Config..........................1X 1X

Voltage Setting Page 
CPU VID Control...........................1.4V
CPU VID Special Add Limit.................Disabled
CPU VID Special Add.......................101.47%
DRAM Voltage Control......................2.103V
SB Core/CPU PLL Voltage...................1.510V
NB Core Voltage...........................1.50V
CPU VTT Voltage...........................1.360V
VCore Droop Control.......................Disabled
Clockgen Voltage Control..................3.45V
GTL+ Buffers Strength.....................Strong
Host Slew Rate............................Strong
MCH RON Offset Value......................00
MCH RTT Offset Value......................00
MCH Slew Rate Offset Value................00
MCH VREF 1 Value..........................00
MCH VREF 2 Value..........................00
MCH VREF 3 Value..........................80
GTL REF Voltage Control...................Enabled
CPU GTL 1/2 REF Volt...................... 88
CPU GTL 1/3 REF Volt...................... 88
North Bridge GTL REF Volt ................ 45

DRAM Timing Page
Enhance Data Transmitting.................Fast
Enhance Addressing........................Fast
T2 Dispatch...............................Disabled
Clock Setting Fine Delay..................Listed Below

CAS Latency Time (tCL)....................5
RAS# to CAS# Delay (tRCD).................5
RAS# Precharge (tRP)......................5
Precharge Delay (tRAS)....................15
All Precharge to Act......................auto
REF to ACT Delay (tRFC)...................auto
Performance Level.........................auto
Read Delay Phase Adjust...................Listed Below
MCH ODT Latency...........................Auto
Write to PRE Delay (tWR)..................auto
Rank Write to Read (tWTR).................auto
ACT to ACT Delay (tRRD)...................auto
Read to Write Delay (tRDWR)...............auto
Ranks Write to Write (tWRWR)..............Auto
Ranks Read to Read (tRDRD)................Auto
Ranks Write to Read (tWRRD)...............Auto
Read CAS# Precharge (tRTP)................auto
ALL PRE to Refresh........................auto

Read Delay Phase Adjust Page
Channel 1 Phase 0 Pull-In.................Auto
Channel 1 Phase 1 Pull-In.................Auto
Channel 1 Phase 2 Pull-In.................Auto
Channel 1 Phase 3 Pull-In.................Auto
Channel 1 Phase 4 Pull-In.................Auto

Channel 2 Phase 0 Pull-In.................Auto
Channel 2 Phase 1 Pull-In.................Auto
Channel 2 Phase 2 Pull-In.................Auto
Channel 2 Phase 3 Pull-In.................Auto
Channel 2 Phase 4 Pull-In.................Auto

Clock Setting Fine Delay Page
DRAM CLK Driving Strength.................Level 5
DRAM Data Driving Strength................Level 8
Ch1 DLL Default Skew Model................Model 0
Ch2 DLL Default Skew Model................Model 0

Fine Delay Step Degree....................5ps


Ch1 Clock Crossing Setting................Auto
DIMM 1 Clock fine delay...................Current  489ps
DIMM 2 Clock fine delay...................Current  489ps
DIMM 1 Control fine delay.................Current  434ps
DIMM 2 Control fine delay.................Current  473ps
Ch 1 Command fine delay...................Current  182ps

Ch2 Clock Crossing Setting................Auto
DIMM 3 Clock fine delay...................Current  686ps
DIMM 4 Clock fine delay...................Current  686ps
DIMM 3 Control fine delay.................Current  607ps
DIMM 4 Control fine delay.................Current  654ps
Ch 2 Command fine delay...................Current  371ps

Ch1Ch2 CommonClock Setting................Auto

Ch1 RDCAS GNT-Chip Delay..................Auto
Ch1 WRCAS GNT-Chip Delay..................Auto
Ch1 Command to CS Delay...................Auto

Ch2 RDCAS GNT-Chip Delay..................Auto
Ch2 WRCAS GNT-Chip Delay..................Auto
Ch2 Command to CS Delay...................Auto

Common CMD to CS Timing...................  auto

[non]

Tweet

^^ sori, koq UT ada skew+ amplitude?

[57.Christ]

Tweet

@roedzzz

itu bios versi brapa ya bro? di g gak ada amplitude ama skewnya..

btw, VTT segitu bkannya dah ngelewatin redline procie g ya bro? jadi serem neh..

**Update

dah bsa jalan di 445, tp cma sampe BIOS doang..sisanya pasti ngehang..klo gak bakalan sering muncul 4E

ada saran lain?

[freaxout]

Tweet

skew + amplitude cuman ada di DK, LT/UT ga ada

[57.Christ]

Tweet

skew + amplitude cuman ada di DK, LT/UT ga ada

klo gitu DK lebih OCable dong dibanding LT/UT? tp bkannya DK lebih murah ya bro?

[roedzzz]

Tweet

Thanks untuk koreksinya..
Maaf kmaren salam tulis..Itu seitngan buat LP UT X48-TRS
Pada UT X48-T2R ternyata memang tidak ada 2 opsi tersebut..

VTT sgitu masih aman klo buat saya..asal jgn lebih dari 1.4v klo buat harian..

[57.Christ]

Tweet

Thanks untuk koreksinya..
Maaf kmaren salam tulis..Itu seitngan buat LP UT X48-TRS
Pada UT X48-T2R ternyata memang tidak ada 2 opsi tersebut..

VTT sgitu masih aman klo buat saya..asal jgn lebih dari 1.4v klo buat harian..

gan, bisa kasi tw panduan kasar cara setting yang CLK driving strength, dll itu gak? ( yang 4 level diatas itu ) hehe, g mo nyeting2 tp gak ngerti sama skali..