Share your voltage setting !!

[roedzzz]

Tweet

Mantabzzz ne biosnya UT..
Itu biosnya LP UT P35 T2R bro obeam..
Jelas aja beda ma T2RS

@febriart_ag
Juli@ dah dijual buat nombokin X38 ya bro???

Mang ada procie Intel yg 46nm pak hazzan???

[D3vastator]

Tweet

Share BIOS setting utk P35 DK T2RS dong...(utk FSB 450-an)
Kalo bisa ada SS nya supaya gampang.
Thanks.

[D3vastator]

Tweet

Bro h4zz4n sharing settingan BIOS nya dong...
Kalo bisa DFI P35 DK T2RS.

[jomblosejati]

Tweet

CPU Feature Page
Thermal Management Control................Disabled
PPM (EIST) Mode...........................Enabled
Limit CPUID MaxVal........................Disabled
CIE Function..............................Auto
Execute Disable Bit.......................Disabled
Virtualization Technology.................Disabled
Core Multi-Processing.....................Enabled

Main BIOS Page
Exist Setup Shutdown......................Mode 2
O. C. Fail Retry Counter..................0
CLOCK VC0 Divider.........................Auto
CPU Clock Ratio...........................8x
CPU N/2 Ratio.............................Disabled
  -Target CPU Clock.......................4120 MHz
CPU Clock.................................515 MHz
Boot Up Clock.............................410
DRAM Speed................................333/667
  -Target DRAM Speed......................DDR2 1030
PCIE Clock................................100MHz
PCIE Slot Config..........................1X 1X

CPU Spread Spectrum.......................Disabled
PCIE Spread Spectrum......................Disabled
SATA Spread Spectrum......................Disabled

Voltage Setting Page 
CPU VID Control...........................1.4125v
CPU VID Special Add.......................Auto
DRAM Voltage Control......................2.15v
SB Core/CPU PLL Voltage...................1.61v
NB Core Voltage...........................1.64v
CPU VTT Voltage...........................1.36v
VCore Droop Control.......................Enabled
Clockgen Voltage Control..................3.60v
GTL+ Buffers Strength.....................Strong
Host Slew Rate............................Weak
GTL REF Voltage Control...................Enabled
CPU GTL 1/3 REF Volt......................85
CPU GTL 0/2 REF Volt......................83
North Bridge GTL REF Volt ................66

DRAM Timing Page
Enhance Data Transmitting.................Fast
Enhance Addressing........................Fast
T2 Dispatch...............................Auto
Clock Setting Fine Delay..................Listed Below
CAS Latency Time (tCL)....................5
RAS# to CAS# Delay (tRCD).................5
RAS# Precharge (tRP)......................5
Precharge Delay (tRAS)....................15
All Precharge to Act......................5
REF to ACT Delay (tRFC)...................54
Performance LVL (Read delay)..............8
Read delay phase adjust...................Listed Below
MCH ODT Latency...........................3
Write to PRE Delay (tWR)..................14
Rank Write to Read (tWTR).................12
ACT to ACT Delay (tRRD)...................4
Read to Write Delay (tRDWR)...............8
Ranks Write to Write (tWRWR)..............5
Ranks Read to Read (tRDRD)................6
Ranks Write to Read (tWRRD)...............5
Read CAS# Precharge (tRTP)................4
ALL PRE to Refresh........................5

Clock Setting Fine Delay Page
Ch1 Clock Crossing Setting................More Aggressive
DIMM 1 Clock fine delay...................LUPA
DIMM 2 Clock fine delay...................LUPA
Ch 1 Command fine delay...................LUPA
CH 1 Control fine delay...................LUPA


Ch2 Clock Crossing Setting................More Aggressive
DIMM 3 Clock fine delay...................LUPA
DIMM 4 Clock fine delay...................LUPA
Ch 2 Command fine delay...................LUPA
CH 2 Control fine delay...................LUPA

Ch1Ch2 CommonClock Setting................More Aggressive

Ch1 RDCAS GNT-Chip Delay..................Auto
Ch1 WRCAS GNT-Chip Delay..................Auto
Ch1 Command to CS Delay...................Auto

Ch2 RDCAS GNT-Chip Delay..................Auto
Ch2 WRCAS GNT-Chip Delay..................Auto
Ch2 Command to CS Delay...................Auto

Read Delay Phase Adjust Page
Ch1 Read delay phase(4~0)    8 - 8 - 8 - 8 - 8 - 8
Channel 1 Phase 0 Pull-In.................Auto
Channel 1 Phase 1 Pull-In.................Auto
Channel 1 Phase 2 Pull-In.................Auto
Channel 1 Phase 3 Pull-In.................Auto
Channel 1 Phase 4 Pull-In.................Auto

Ch2 Read delay phase(4~0)    8 - 8 - 8 - 8 - 8 - 8
Channel 2 Phase 0 Pull-In.................Auto
Channel 2 Phase 1 Pull-In.................Auto
Channel 2 Phase 2 Pull-In.................Auto
Channel 2 Phase 3 Pull-In.................Auto
Channel 2 Phase 4 Pull-In.................Auto

Vcore mestinya masih bisa turun lagi, tapi lagi pusing utak-atik VTT dan GTL Ref. Yah, minimal di 4.12 GHz Prime 95 blend udah 2 jam masih lolos sih.

[simon1313ind]

Tweet

@pak jomblo
jalan cl 4 pak??
cobain gtl berurutan 68,68,70
mudahan v corenya bisa turun

[jomblosejati]

Tweet

CL 5 bro, sementara RAM ane set yg enteng2 aka kendor2 aja, lagi coba lihat max CPUnya nih (tapi kayaknya memang CPUnya kurang bagus).

[D3vastator]

Tweet

NB Core Voltage...........................1.64v

Itu NB Core Voltage gunanya utk apa ya?
Kenapa harus tinggi sekali (1,64V)?

GRP sent
Thanks.

[anubis2004]

Tweet

Itu NB Core Voltage gunanya utk apa ya?
Kenapa harus tinggi sekali (1,64V)?

Harus spread GRP dulu nih...
Thanks.

ktnya sich utk mendukung FSB yg cukup tinggi..tp utk kuran 1.6 itu jg dah tinggi skali, 1.5 dah sharusnya sich cukup..heatsink DFI buat NBnya jg kyanya kurang bagus

[simon1313ind]

Tweet

supaya stabil di FSB tinggi entah tarikan proc atau ram
NB sih masih mending lah,klo yang SB disetrum terlalu tinggi bisa corrupt HDD nya
gue pernah kejadian soalnya

[jomblosejati]

Tweet

Kenapa Vnb digenjot tinggi ? Karena lagi ngejar high FSB, cari settingan RAM yg sip, ane kasih rada tinggi biar memory controller gak jadi bottleneck. Nantinya kalo dah stabil, mungkin bakal dicoba diturunkan dikit demi sedikit. Tapi dgn semburan Nidec Beta TA450 @2800-an RPM (kira2), suhu chipset gak pernah lewat 50 c kok, and suhu system (PWM ?) gak pernah lewat 48 c, saat dites Prime95 Blend 2+ jam.