Share your voltage setting !!

[budirahmat]

Tweet

Ikutan Sharing yaa...
Spesifikasi : See My System
E6550 2,3Ghz@3593,2 (vcore bios 1,26250v) (CPUz Validation)
Spesifikasi Rig : see my system
BATCH : L723B017
spi32M (link)

Complete Voltage Setting :

Main BIOS Page
Exist Setup Shutdown......................Mode 2
O. C. Fail Retry Counter..................1
CLOCK VC0 Divider.........................Auto
CPU Clock Ratio...........................7x
Target CPU Clock..........................3591 MHz
CPU Clock.................................513 MHz
Boot Up Clock.............................Auto
DRAM Speed................................333/667
  -Target DRAM Speed......................DDR2 1027
PCIE Clock................................100MHz
PCIE Slot Config..........................1X 1X

CPU Spread Spectrum.......................Disabled
PCIE Spread Spectrum......................Disabled
SATA Spread Spectrum......................Disabled

CPU Feature Page
Thermal Management Control................Disabled
PPM (EIST) Mode...........................Disabled
Limit CPUID MaxVal........................Disabled
CIE Function..............................Disabled
Execute Disable Bit.......................Disabled
Virtualization Technology.................Disabled
Core Multi-Processing.....................Enabled

Voltage Setting Page 
CPU VID Control...........................1.26250v
CPU VID Special Add Limit.................Disable
CPU VID Special Add.......................Disable
DRAM Voltage Control......................2.350v
SB 1.05v Voltage..........................1.300v
SB Core/CPU PLL Voltage...................2.15v
NB Core Voltage...........................1.37v
CPU VTT Voltage...........................1.28v
VCore Droop Control.......................Enabled
Clockgen Voltage Control..................3.45v
GTL+ Buffers Strength.....................Strong
Host Slew Rate............................Weak
GTL REF Voltage Control...................Enabled
CPU GTL 1/3 REF Volt......................80
CPU GTL 0/2 REF Volt......................80
North Bridge GTL REF Volt ................90

DRAM Timing Page
Enhance Data Transmitting.................Fast
Enhance Addressing........................Fast
T2 Dispatch...............................Disable
Clock Setting Fine Delay..................Listed Below
CAS Latency Time (tCL)....................4
RAS# to CAS# Delay (tRCD).................4
RAS# Precharge (tRP)......................4
Precharge Delay (tRAS)....................12
All Precharge to Act......................Auto
REF to ACT Delay (tRFC)...................Auto
Performance LVL (Read delay)..............Auto
Read delay phase adjust...................Listed Below
MCH ODT Latency...........................Auto
Write to PRE Delay (tWR)..................Auto
Rank Write to Read (tWTR).................Auto
ACT to ACT Delay (tRRD)...................Auto
Read to Write Delay (tRDWR)...............Auto
Ranks Write to Write (tWRWR)..............Auto
Ranks Read to Read (tRDRD)................Auto
Ranks Write to Read (tWRRD)...............Auto
Read CAS# Precharge (tRTP)................Auto
ALL PRE to Refresh........................Auto

Clock Setting Fine Delay Page
Ch1 Clock Crossing Setting................More Aggressive
DIMM 1 Clock fine delay...................1324
DIMM 2 Clock fine delay...................474
Ch 1 Command fine delay...................874
CH 1 Control fine delay...................412


Ch2 Clock Crossing Setting................More Aggressive
DIMM 3 Clock fine delay...................1200
DIMM 4 Clock fine delay...................386
Ch 2 Command fine delay...................924
CH 2 Control fine delay...................300

Ch1Ch2 CommonClock Setting................More Aggressive

Ch1 RDCAS GNT-Chip Delay..................Auto
Ch1 WRCAS GNT-Chip Delay..................Auto
Ch1 Command to CS Delay...................Auto

Ch2 RDCAS GNT-Chip Delay..................Auto
Ch2 WRCAS GNT-Chip Delay..................Auto
Ch2 Command to CS Delay...................Auto

Read Delay Phase Adjust Page
Ch1 Read delay phase(4~0)    8 - 8 - 8 - 8 - 8 - 8
Channel 1 Phase 0 Pull-In.................Auto
Channel 1 Phase 1 Pull-In.................Auto
Channel 1 Phase 2 Pull-In.................Auto
Channel 1 Phase 3 Pull-In.................Auto
Channel 1 Phase 4 Pull-In.................Auto

Ch2 Read delay phase(4~0)    8 - 8 - 8 - 8 - 8 - 8
Channel 2 Phase 0 Pull-In.................Auto
Channel 2 Phase 1 Pull-In.................Auto
Channel 2 Phase 2 Pull-In.................Auto
Channel 2 Phase 3 Pull-In.................Auto
Channel 2 Phase 4 Pull-In.................Auto

Saya terpaksa menggunakan SB voltage yang maksimal (2,15v) , kalo dibawah itu justru gak masuk windows.
Anehnya saya masih pake Vcore, Vnb, VTT yang masih rendah lho

[budirahmat]

Tweet

CHIP Error melulu ... Double post jadinya
Delete please !

[indrasukmab]

Tweet

@budirahmat
Mas tu setinganny buat daily?terus kok SB nya dipasang tinggi banget?SB bukannya buat yang berhubungan sama HDD,optical drive,soundcard dll?ada kemungkinan gosong ga tuh?
oya kalo salah tlg dikoreksi ya
maturnuwun

[budirahmat]

Tweet

@budirahmat
Mas tu setinganny buat daily?terus kok SB nya dipasang tinggi banget?SB bukannya buat yang berhubungan sama HDD,optical drive,soundcard dll?ada kemungkinan gosong ga tuh?
oya kalo salah tlg dikoreksi ya
maturnuwun

Iya bro...settingan tersebut buat daily. Permasalahan saya cuma pada SB tsb, ketinggian mungkin. Tapi kalo dilihat suhunya, adem2 aja tuuh. Makanya saya pingin share ama master-master disini.

Ohyaa...sejauh ini masih nyampe di FSB 518, vcore bios : 1,280v (validasi)

[D3vastator]

Tweet

Saya terpaksa menggunakan SB voltage yang maksimal (2,15v) , kalo dibawah itu justru gak masuk windows.
Anehnya saya masih pake Vcore, Vnb, VTT yang masih rendah lho

Hati2 HDD jadi error atau bad sector, bro...

[indrasukmab]

Tweet

@budirahmat
gileee procie nya sakti tuh..tapi apa ga kasian mobo nya juga?harian buat jalan segitu??

[budirahmat]

Tweet

Hati2 HDD jadi error atau bad sector, bro...

@budirahmat
gileee procie nya sakti tuh..tapi apa ga kasian mobo nya juga?harian buat jalan segitu??

Setelah saya setting ulang, ternyata, akibat kipas 8cm yang saya letakkan tepat diatas northbridge justru mengacaukan sistem suhu di MB & Procie. Setelah saya lepaskan dan cuma mengandalkan kipas intake 12cm didepan, 12 cm di belakang Noctua Fan in&out pada HSF Noctua-NHU12P serta kipas raksasa ICUTE 18
JADINYA ... Vsb turun jadi 1,75v (dari semula 2,15v) , SB 1,05v voltagenya juga turun menjadi 1,217v (semula 1,300v), dan Vdimmnya juga turun jadi 2,31 di bios. ALL SETTING sama seperti yang saya report sebelum ini.
Dan suhunya juga jadi lebih adem. see SS deeh

[illusionist84]

Tweet

pusiiiinnnggg,, ajarin dong biar ngerti udah pake system ok tp blum ngerti dan pengen bisa,, ada yang punya link atau apalah buat gw blajar