bios DFI LP UT P45 T2RS neh...

[roedzzz]

Tweet

Untuk Vcore sama VDimm disesuaikan dgn kemampuan procie anda bro
Itu setingan buat procie dan RAM saya..
Untuk LP DK P45 -T2RS+ seh saya rasa dgn tanpa merubah setingan apapun selain Vcore dan VDimm bisa dgn mudah harusnya klo jalan 400*8

Paling enak klo saya pribadi seh step by step naikin fsb dari default tanpa menyentuh voltase dahulu..
Klo sudah ga mau boot sampe windows baru opsi voltasenya dimainkan..

[dying_in]

Tweet

Share aja buat yg pake DFI LP UT P45-T2RS..
Ini setinganku buat fsb 600*7.5..Gue pake bios beta 10/28..
Setingan ini stabil buat systemku dipake shari-hari

CPU Feature:
 
Thermal Management Control.......... - Disabled
PPM(EIST) Mode...................... - Disabled
Limit CPUID MaxVal.................. - Disabled
CIE Function........................ - Disabled
Execute Disable Bit................. - Disabled
Virtualization Technology........... - Disabled
Core Multi-Processing............... - Enabled
 
DRAM Timing:
 
Enhance Data transmitting........... - Fast
Enhance Addressing.................. - Fast
T2 Dispatch......................... - disable

Clock Setting Fine Delay Press Enter:

DLL And RCOMP Settings.............. - manual
Ch1 Dram Defaul Skew................ - Model 7
Ch2 Dram Defaul Skew................ - Model 7
RCOMP Settings...................... - Model 1

Fine Delay Step Degree.............. - 70ps
Ch1 Clock Crossing Setting.......... - Auto
DIMM1 Clock Fine Delay.............. - Current[2396ps]
DIMM2 Clock Fine Delay.............. - Current[2396ps]
Ch1 Control0 Fine Delay............. - Current[268ps]
Ch1 Control1 Fine Delay............. - Current[268ps]
Ch1 Control2 Fine Delay............. - Current[268ps]
Ch1 Control3 Fine Delay............. - Current[268ps]
Ch1 Command Fine Delay.............. - Current[394ps]

Ch2 Clock Crossing Setting.......... - Auto
DIMM3 Clock Fine Delay.............. - Current[2066ps]
DIMM4 Clock Fine Delay.............. - Current[2066ps]
Ch2 Control0 Fine Delay............. - Current[48ps]
Ch2 Control1 Fine Delay............. - Current[48ps]
Ch2 Control2 Fine Delay............. - Current[48ps]
Ch2 Control3 Fine Delay............. - Current[48ps]
Ch2 Command Fine Delay.............. - Current[394ps]

Ch1 Ch2 Common Clock Setting........ - Auto

Ch1 RDCAS GNT-Chip Delay............ - Auto
Ch1 WRCAS GNT-Chip Delay............ - Auto
Ch1 Command To CS Delay............. - Auto
.
Ch2 RDCAS GNT-Chip Delay............ - Auto
Ch2 WRCAS GNT-Chip Delay............ - Auto
Ch2 Command To CS Delay............. - Auto

Flex Memory Mode..................... - Auto
CAS Latency Time (tCL)............... - 5
RAS# to CAS# Delay (tRCD)............ - 5
RAS# Precharge (tRP)................. - 5
Precharge Delay (tRAS)............... - 15
All Precharge to Act................. - auto
REF to ACT Delay (tRFC).............. -52
Performance Level.................... - 10

Read delay phase adjust Press Enter:

Channel 1 Phase 0 Pull-In........... - Auto
Channel 1 Phase 1 Pull-In........... - Auto
Channel 1 Phase 2 Pull-In........... - Auto
Channel 1 Phase 3 Pull-In........... - Auto
Channel 1 Phase 4 Pull-In........... - Auto

Channel 2 Phase 0 Pull-In........... - Auto
Channel 2 Phase 1 Pull-In........... - Auto
Channel 2 Phase 2 Pull-In........... - Auto
Channel 2 Phase 3 Pull-In........... - Auto
Channel 2 Phase 4 Pull-In........... - Auto

Write to PRE Delay (tWR)............ - auto
Rank Write to Read (tWTR)........... - auto
ACT to ACT Delay (tRRD)............. - 4
Read to Write Delay (tRDWR)......... - 9
Ranks Write to Write (tWRWR)........ - Auto
Ranks Read to Read (tRDRD).......... - Auto
Ranks Write to Read (tWRRD)......... - Auto
ALL PRE to Refresh.................. - Auto

Voltage Settings:

CPU VID Control..................... - 1.55V
CPU VID Special Add................. - disable
CPU VID Special Add................. - 0.147%
DRAM Voltage Control................ - 2.27v
SB Core/CPU PLL Voltage............. - 1.75v
NB Core Voltage..................... - 1.455v
CPU VTT Voltage..................... - 1.367v
Vcore Droop Control................. - Enabled
Clockgen Voltage Control............ - 3.60v
GTL+ Buffer Strength................ - Strong
CPU GTL 0 REF Volt.................. - 0.6125
CPU GTL 2 REF Volt.................. - 0.6125
CPU GTL 1 REF Volt.................. - 0.6125
CPU GTL 3 REF Volt.................. - 0.6125
North Bridge GTL 0 REF Volt......... - 0.6050
North Bridge GTL 1 REF Volt......... - 0.6050
FSB Vref............................ - 00
 
Genie BIOS Settings:
 
Exist Setup Shutdown................ - Mode 2
Exist Shutdown After AC loss........ - Enabled
AC Shutdown Free.................... - Enabled
O.C Clock Fail Retry Counter........ - 0
O.C Clock Fail CMOS Reloaded........ - Disabled
CPU Clock Ratio..................... - 7.5
CPU N/2 Ratio....................... - Enable
Target CPU Clock.................... - 4500MHz
CPU Clock........................... - 600
Boot Up Clock....................... - Auto
CPU Clock Amplitude................. - 900mV
CPU Clock0 Skew..................... - 200ps
CPU Clock1 Skew..................... - 0ps
DRAM Speed.......................... - 333/667
Target DRAM Speed................... - 1201MHz
PCIE Clock.......................... - 100mhz
PCIE Slot Config.................... - 1x 1x 
CPU Spread Spectrum................. - Disabled
PCIE Spread Spectrum................ - Disabled

wahh...

thanx bgt neh bro...

gw jdi pgn nyoba neh settingan..
tpi klo gw blum punya pendingin kira2 neh setingan aman g'bro???

[Fachri]

Tweet

dan settingan jg beda utk setiap proc, gw pake Q6600, kalau mau OC settingannya harus :
CPU Clock Amplitude................. - 800mV
CPU Clock0 Skew..................... - 200ps
CPU Clock1 Skew..................... - 0ps

di lain itu malah bikin makin kecil overclock nya.
Ati2 naikin SB core, karena southbridge sebenernya ngga perlalu terlalu di overclock karena FSB itu adan di northbridge

[M.art lover]

Tweet

wahh...

thanx bgt neh bro...

gw jdi pgn nyoba neh settingan..
tpi klo gw blum punya pendingin kira2 neh setingan aman g'bro???

kalau diliat dari settingnya sih masih cukup aman buat daily bro.betul begitu om roedzz??
tambahin bbrp fan aja bro kl kurang yakin

[roedzzz]

Tweet

Setingan untuk fsb 600*7.5 atau 600*7 mesthi pake cooling yg bagus untuk procie dgn airflow casing yg bagus..
Selain itu pastikan RAM anda kuat bro jalan di 600/1200mhz..
Harap jg diperhatikan klo saya ga pake casing bro..Jadi system ga panas banget..

Sebaiknya dicoba step by step per 20-50mhz dulu naikin fsbnya..
Jgn langsung main hajar 600*7.5..Jadi kita bisa tahu kekurangannya dimana nanti..
Setingan saya di atas hanya sekedar buat gambaran aja bro

[a603nk]

Tweet

mantab kang roedzzz GRP senttttttt

[cyber_shinigami]

Tweet

Walah gw kok ga isa nyampe 4.0 ya ? 450 x 9 dengan ratio 1:1 aja gak mau booting di BIOS nya diem di tulisan procie nya klu gak setelah tulisan procie kluar " Memory Te " udah deh pas direset bunyi tit.tit.tit dempet ? apa yg salah ya ?
Pake 500 x 8 ratio 1:1 lebih parah BIOS aja gak mau masuk ?

Mantab gw dah coba setting RAM nya sep punya bro

[dying_in]

Tweet

Setingan untuk fsb 600*7.5 atau 600*7 mesthi pake cooling yg bagus untuk procie dgn airflow casing yg bagus..
Selain itu pastikan RAM anda kuat bro jalan di 600/1200mhz..
Harap jg diperhatikan klo saya ga pake casing bro..Jadi system ga panas banget..

Sebaiknya dicoba step by step per 20-50mhz dulu naikin fsbnya..
Jgn langsung main hajar 600*7.5..Jadi kita bisa tahu kekurangannya dimana nanti..
Setingan saya di atas hanya sekedar buat gambaran aja bro

iya bro...
gw dah coba neh OC di 360*9..
sukses....
hahaha...
OC pertama gw seumur hidup...
sukses dy lari di 3240 MHz.....

tpi pas gw coba di 600*6 kq g'mw boot y bro???
bisa nya cuma di bawah 533???

apa yg musti di setting lagi bro???
apa ada panel2 tertentu di mobo nya yg musti di ubah2 letaknya???

[Gotjap]

Tweet

Sorry agak OOT dikit...

kalo liat disini:

http://www.viraindo.com/pc1.html

kok harganya lebih murah dari yg seri DK ya? apa ada spek yg dikurangi ya...?

kalo emang bener harganya segitu jadi pengen nyoba juga ni...

thanks...

[dying_in]

Tweet

Sorry agak OOT dikit...

kalo liat disini:

http://www.viraindo.com/pc1.html

kok harganya lebih murah dari yg seri DK ya? apa ada spek yg dikurangi ya...?

kalo emang bener harganya segitu jadi pengen nyoba juga ni...

thanks...

hmmm....
setau gw sie bro yg nma nya DFI ntu seri UT lbih mhal dari yg DK..

truz jg klo gw liat di rakitan.com yg hrga segitu ntu DFI LP DK P45 T2RS...

untuk lbih jlas nya bro tanya aja deh ama bro V.O.C, kyaknya beliau deh distributor DFI dsini...
hehehe....