TEMPLATE BIOS utk Motherboard Gigabyte

[alisundoro]

Tweet

Permisi para senior...
Mo nyumbang BIOS Template aja neh...

Berhubung sy baru make Gigabyte sejak X58 UD3R. Pas kebetulan cari informasi di internet,
ketemu forum www.tweaktown.com. ini linknya

di situ ada representative dari Gigabyte.. n mereka punya template yg BIOS yg baik...
terimakasih kepada LSDMEASAP. yang sudah membuatkan template ini..
saya hanya meneruskan saja.. saya tidak punya hak apa2 atas template ini loh..

menurut sy sih.. bagus buat kita2 sebagai standar menanyakan tentang setting BIOS...
sehingga semua orang memiliki persepsi yang sama dan memudahkan komunikasi..
terutama untuk orang cupu macam saya ini..

gampang saja kok... template bios nya dicopy aja ke note pad.. kemudian nilai2nya diganti dengan nilai BIOS yang dimiliki.
kemudian tinggal di post balik ke forum.

Sebaiknya dalam memposting template ini juga dicantumkan informasi tambahan seperti

CPU = Model #
Motherboard = Model, Revision #
BIOS Version =
Ram = Brand, Model#, Part#, beserta Link

so langsung saja...

Untuk Motherboard Seri X58 n P55/P57

jika terjadi BSOD. liat ada code nya..

0X00000050 << Incorrect Memory Timing/Freq or Uncore Multi
0X00000124 << Incorrect QPI/Vtt Voltage (To Much/Not Enough)
0X00000101 << Not enough Vcore Voltage

motherboard seri X58

Courtesy of LSDMEASAP dari tweaktown.com

Advanced CPU Features:
CPU Clock Ratio ................................ [20x]
Intel(R) Turbo Boost Tech .................. [Enabled]
CPU Cores Enabled ............................ [All]
CPU Multi Threading .......................... [Enabled]
CPU Enhanced Halt (C1E) ................... [Disabled]
C3/C6/C7 State Support .................... [Disabled]
CPU Thermal Monitor ......................... [Enabled]
CPU EIST Function ............................ [Disabled]
Virtualization Technology ................... [Enabled] << Disabled if you do not use Vmware or Virtual PC Programs
Bi-Directional PROCHOT ..................... [Enabled]


Uncore & QPI Features:
QPI Link Speed .............................. x36
Uncore Frequency ..........................  (Always 2x memory Multi or 2x +1)
Isonchronous Frequency ..................[Enabled]


Standard Clock Control:
Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) .....................
PCI Express Frequency (MHz) ........... [100]

C.I.A.2 [Disabled]

Advanced Clock Control:
CPU Clock Drive ..............................[800mV]
PCI Express Clock Drive ................... [900mV]
CPU Clock Skew ............................. [0ps]
IOH Clock Skew ............................. [0ps]


Advanced DRAM Features:
Performance Enhance ...................... [Standard]
Extreme Memory Profile (X.M.P) ......... [Disabled]
System Memory Multiplier (SPD) ........ [AUTO]
DRAM Timing Selectable (SPD) .......... [Manual]

Channel A + B + C

Channel A Timing Settings:
##Channel A Standard Timing Control##
CAS Latency Time ......................
tRCD .......................................
tRP .........................................
tRAS .......................................

Below values may be left in Auto if you like, generally this is fine.  For those users who DO Set advanced timings manually, please see some of my thoughts and findings about these settings and rules here
XtremeSystems Forums - View Single Post - Gigabyte EX58-UD5/Extreme Discussion Thread

##Channel A Advanced Timing Control##
tRC ........................................  (Should be = tRAS + tRP or above for stability)
tRRD .......................................
tWTR ...................................... (Must be Write to Read Delay/Same Rank - (tWL + 4)
tWR ........................................
tWTP .......................................   (tWTP Must = tWR + tWL + 4)
tWL ........................................    (tWL Must be CAS Latency -1)
tRFC .......................................
tRTP .......................................
tFAW ......................................
Command Rate (CMD) ................

##Channel A Misc Timing Control##
Round Trip Latency ...................



Advanced Voltage Control:

CPU
Load Line Calibration ................. [Disabled]
CPU Vcore ...............................
QPI/VTT Voltage 1.150v ............
CPU PLL 1.800v .......................

MCH/ICH
PCIE 1.500v ...........................
QPI PLL 1.100v .......................
IOH Core 1.100v .....................
ICH I/O 1.500v .......................
ICH Core 1.1v ........................

DRAM
DRAM Voltage 1.500v ..............
DRAM Termination 0.750v [AUTO]
Ch-A Data VRef. 0.750v [AUTO]
Ch-B Data VRef. 0.750v [AUTO]
Ch-C Data VRef. 0.750v [AUTO]
Ch-A Address VRef. 0.750v [AUTO]
Ch-B Address VRef. 0.750v [AUTO]
Ch-C Address VRef. 0.750v [AUTO]

[alisundoro]

Tweet

Untuk Motherboard seri P55 / P57

Courtesy of LSDMEASAP. dari tweaktown.com

Advanced Frequency Settings:

CPU Clock Ratio 21x

Advanced Core Features  [Press Enter]:

Intel(R) Turbo Boost Tech................[Disabled]
CPU Cores Enabled........................[All]
CPU Multi-Threading......................[Disabled]
CPU Enhanced Halt (C1E)..................[Auto]
C3/C6/C7 State Support...................[Auto]
CPU Thermal Monitor......................[Auto]
CPU EIST Function........................[Auto]
Bi-Directional PROCHOT...................[Auto]

QPI Clock Ratio..........................[Auto]
QPI Link Speed........................[x]
Uncore Clock Ratio....................[18x]
Uncore Frequency.........................3600MHz

>>>>>   Standard Clock Control <<<<<

Base Clock (BCLK) Control................[Enabled]
BCLK Frequency ..........................[200]
Extreme Memory Profile (X.M.P.)..........[Disabled]
System Memory Multiplier (SPD)...........[Disabled]
Memory Frequency (MHz)................2000
PCI Express Frequency (MHz)..............[Auto]
C.I.A.2..................................[Disabled]

>>>>>   Advanced Clock Control   <<<<<

CPU Clock Drive..........................[ 800mV]
PCI Express Clock Drive..................[ 900mV]
CPU Clock Skew...........................[    0ps]

Advanced Memory Settings:

Extreme Memory Profile (X.M.P.)..........[Disabled]
System Memory Multiplier (SPD)...........[10.0]
Memory Frequency (MHz)................2000
Performance Enhance   (SPD)............. [Turbo]
DRAM Timing Selectable (SPD)............ [Expert]
Profile DDR Voltage ..................
Profile QPI Voltage ..................
Channel Interleaving.....................[Auto]
Rank Interleaving........................[Auto]

>>>>>   Channel A & B

Channel A Timing Settings            [Press Enter]:
Cas Latency Time........................[8]
tRCD....................................[8]
tRP.....................................[9]
tRAS...................................[24]

>>>>>   Advanced Timing Control

tRC....................................[Auto]
tRRD...................................[Auto]
tWTR...................................[Auto]
tWR....................................[Auto]
tWTP...................................[Auto]
tWL....................................[Auto]
tRFC...................................[Auto]
tRTP...................................[Auto]
tFAW...................................[Auto]
Command Rate (CMD).................. 1 [1]

>>>>>   Misc Timing Control

B2B Cas Delay..........................[Auto]
Round Trip Latency.....................[Auto]

Channel A Turnaround Settings [Press Enter]:
Different DIMMs........................[Auto]
Different DIMMs........................[Auto]
On The Same Rank.......................[Auto]

>>>>>   Channel A Writes Followed By Writes

Different DIMMs........................[Auto]
Different DIMMs........................[Auto]
On The Same Rank.......................[Auto]


Advanced Voltage Settings:

******Mother Board Voltage Control ******
Voltage Types............Normal......Current
--------------------------------------------

>>> CPU
Load Line Calibration...................[Level 2]
CPU Vcore..................1.19375v..[1.xv]
QPI/VTT Voltage..........1.100v.....[1.x00v]

>>> MCH/ICH
PCH Core....................1.050v.....[Auto]
CPU PLL......................1.800v.....[Auto]

>>> DRAM
DRAM Voltage..............1.500v.....[1.660v]
DRAM Termination.........0.750v.....[Auto]
Ch-A Data VRef............0.750v.....[Auto]
Ch-A Data VRef............0.750v.....[Auto]
Ch-B Data VRef............0.750v.....[Auto]
Ch-B Data VRef............0.750v.....[Auto]


Miscellaneous Settings:[/SIZE]

Isochronous Support....................[Enabled]
Virtualisation technology..............[Enabled]
USB Storage Detect ....................[Disabled] Located In Integrated Peripherals Page

[alisundoro]

Tweet

Motherboard Seri P45 / P43 (termasuk G45/G43)

Courtesy of LSDMEASAP. dari tweaktown.com


MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto or Fast
CPU Clock Ratio ..........................: 
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 


Clock Chip Control 
Standard Clock Control
CPU Host Clock Control..................: [Enabled] 
CPU Host Frequency (Mhz) ............: Mhz
PCI Express Frequency (Mhz) .........:Set to 100

C.I.A.2 .................................:[Disabled]


Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 
MCH Clock Skew (ps)...................: <<< 


DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 
Memory Frequency (Mhz) ..............: 
DRAM Timing Selectable ................: [Manual]

Standard Timing Control
CAS Latency Time........................
tRCD .........................................
tRP'...........................................
tRAS..........................................

Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go

Advanced Timing Control
tRRD...........................................
tWTR..........................................
tWR............................................
tRFC...........................................
tRTP...........................................
Command Rate (CMD) ....................:2

Driving Strength Profiles
Driving Strength ............................

Channel A
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
 tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

Channel B
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
 tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

Motherboard Voltage Control

CPU
CPU Vcore….……….........................:Auto if not overclocking, if you are overclocking please do find and set your own voltages

CPU Termination…..... 1.200V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.2-1.5 depending on Vcore, try to keep at least .1 under vcore.  Auto is fine if not overclocking

CPU PLL…………………....1.500V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.5-1.65.  Auto is fine if not overclocking

CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 

CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly 

MCH/ICH
MCH Core…………….....1.100V...........: << 
MCH Reference….…….0.760V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.500V............: <<< Leave
ICH Core…………...……1.100V............: <<< Leave

DRAM
DRAM Voltage ……....1.800V............: 
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB

[alisundoro]

Tweet

Untuk Motherboard Seri P35 dan X38/X48 (termasuk P31, G31 dan 965P)

Courtesy of LSDMEASAP. dari tweaktown.com


Robust Graphics Booster___________ [Auto]
CPU Clock Ratio ____________ [8] 
Fine Clock Ratio ____________[0.5]
CPU Host Clock Control_ [Enabled]
CPU Host Frequency (MHz)__________ [450] 
PCI Express Frequency (Mhz)_______ [100]
C.I.A. 2__________________________ [Disabled]
System Memory Multiplier (SPD)____ [2.00]
DRAM Timing Selectable_______ SPD __ [Manual]

Performance Enhance = [Standard]

CAS Latency Time________________ 
Dram RAS# to CAS# Delay_________ 
Dram RAS# Precharge Delay_______
Precharge Delay (tRAS)__________ 

ACT to ACT Delay (tRRD)_________ 
Rank Write to READ Delay________ 
Write to Precharge Delay_________ 
Refresh to ACT Delay______________ 
Read to Precharge Delay__________
Static tRead Value_______________
Static tRead Phase Adjust________ [Auto]

CPU/PCIEX Clock Driving Control [800mV]
CPU Clock Skew Control [normal]
GMCH Clock Skew Control [Normal]

System Voltage Control____ [Manual]
DDR2 OverVoltage Control__ [+0.300V] 
PCI-E OverVoltage Control_ [+0.1V] 
FSB OverVoltage Control___ [+0.1V] 
(G)MCH OverVoltage Control [+0.1V] 
CPU Voltage Control_______ [1.25]

Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

Integrated Peripherals
Legacy USB Storage Detect___________________[Disabled] *Note* Must be enabled to flash from USB

[Yz_]

Tweet

nice share......mumpung ada mobo X58,sambil menyambut i7 930
cendoll sent......

[ovan febriawan]

Tweet

wah info yang sangat berguna bos

[alisundoro]

Tweet

Mdh2an bs membantu utk mempermudah komunikasi nya y.

[w3ztb0y]

Tweet

Maap nubie numpang nanya, template BIOS apaan yah???trus fungsinya bwat apa??

[alisundoro]

Tweet

Maksud nya biar gampang konsultasi ama chipers laen terutama pemakai mobo gigabyte ttg setting bios.
Contohnya dlm peng over clocking.

[kriee]

Tweet

ohh ... dulu sering baca juga, klo di amatin enak juga komunkasinya trutama tuk settingan BIOS scra OC ...

maap mw tanya.

jika terjadi BSOD. liat ada code nya..

0X00000050 << Incorrect Memory Timing/Freq or Uncore Multi
0X00000124 << Incorrect QPI/Vtt Voltage (To Much/Not Enough)
0X00000101 << Not enough Vcore Voltage

smuanya itu kliatannya dimananya ya .... , terkdangn cepet juga BSODnya sampai gak bisa baca apa2 ...