bios DFI LP UT P45 T2RS neh...

[prahasta]

Tweet

he he he. yang jelas, makin susah, makin menantang buat newbie kayak gue. kalo enggak mungkin dah gue lego nih board ha ha

[Fachri]

Tweet

gw bru beli DFI LP UT P45,, maknyus bgt.. tpi gw bingung neh am bios nya, ada yg bisa ngereview bios neh mobo g'?

am tutorial2 yg bagus buat OC neh mobo,,

thanx yah???

hhahahaa, sama gw jg pernah pake mobo ini.....ampuuuun ribet banget advance bios nya, tapi kalau yg bener overclocker freak bagus banget price performance nih mobo, karena kalau sampai ketemu setting yg pas buat spek sendirim bisa oc tinggi banget, cuma musti coba2 dulu.
Kelemahannya mobo ini, keliatannya divider 333/800 nya belum officially supported sama BIOS, karena dulu pas coba overclock pake divider itu mau FSB berapa pun pasti ngga bisa di benchmark.

Cek3 review yg dah di kasih di atas tuh, atau coba juga cari di internet ABS (auto boost system) file nya utk spek processor yg sama, siapa tau ada yg cocok, kemaren coba2 ini baru ketemu yg cocok.

[dying_in]

Tweet

thanx buat bro2 yg da ngasih saran..
n tmbah buat gua puyeng.,,,

cz gua newbie..
baru beli kompter,,,
pengen jadi OC..
tpi g'taw mau mulai dari mna..

thanx bro..
gua bakal coba pelajarin lagi neh mobo...

[dying_in]

Tweet

emang binggung nya dimana bro?

bingung mau mulai dari mana nya...
gg tau mau ngapain..

blom ada guru...

[a603nk]

Tweet

bingung mau mulai dari mana nya...
gg tau mau ngapain..

blom ada guru...

aduh coba baca2 ini bro

http://www.clunk.org.uk/forums/overc...s-dfi-add.html

ikutin step2nya trial and error

[ahoey_amj]

Tweet

Jangankan yg tipe UT..... Ini aja mode trial + error = Clear CMOS.. di seri DK-nya aja dah bikin ruwet kepala owe yg lagi testbed sendiri ditoko... Tp mmg owe akuin kalo nih mobo mmg maknyuzzz klo soal OC... Testbed pake E7300, utak-atik dikiiit di Genie BIOS DFI..., Bim Salabim..!! Langsung jalan di 4GHz (testing pake Prime95 @2 jam = No Error!)

[cyber_shinigami]

Tweet

Jangankan yg tipe UT..... Ini aja mode trial + error = Clear CMOS.. di seri DK-nya aja dah bikin ruwet kepala owe yg lagi testbed sendiri ditoko... Tp mmg owe akuin kalo nih mobo mmg maknyuzzz klo soal OC... Testbed pake E7300, utak-atik dikiiit di Genie BIOS DFI..., Bim Salabim..!! Langsung jalan di 4GHz (testing pake Prime95 @2 jam = No Error!)

Walah gw kok ga isa nyampe 4.0 ya ? 450 x 9 dengan ratio 1:1 aja gak mau booting di BIOS nya diem di tulisan procie nya klu gak setelah tulisan procie kluar " Memory Te " udah deh pas direset bunyi tit.tit.tit dempet ? apa yg salah ya ?
Pake 500 x 8 ratio 1:1 lebih parah BIOS aja gak mau masuk ?

[roedzzz]

Tweet

Share aja buat yg pake DFI LP UT P45-T2RS..
Ini setinganku buat fsb 600*7.5..Gue pake bios beta 10/28..
Setingan ini stabil buat systemku dipake shari-hari

CPU Feature:
 
Thermal Management Control.......... - Disabled
PPM(EIST) Mode...................... - Disabled
Limit CPUID MaxVal.................. - Disabled
CIE Function........................ - Disabled
Execute Disable Bit................. - Disabled
Virtualization Technology........... - Disabled
Core Multi-Processing............... - Enabled
 
DRAM Timing:
 
Enhance Data transmitting........... - Fast
Enhance Addressing.................. - Fast
T2 Dispatch......................... - disable

Clock Setting Fine Delay Press Enter:

DLL And RCOMP Settings.............. - manual
Ch1 Dram Defaul Skew................ - Model 7
Ch2 Dram Defaul Skew................ - Model 7
RCOMP Settings...................... - Model 1

Fine Delay Step Degree.............. - 70ps
Ch1 Clock Crossing Setting.......... - Auto
DIMM1 Clock Fine Delay.............. - Current[2396ps]
DIMM2 Clock Fine Delay.............. - Current[2396ps]
Ch1 Control0 Fine Delay............. - Current[268ps]
Ch1 Control1 Fine Delay............. - Current[268ps]
Ch1 Control2 Fine Delay............. - Current[268ps]
Ch1 Control3 Fine Delay............. - Current[268ps]
Ch1 Command Fine Delay.............. - Current[394ps]

Ch2 Clock Crossing Setting.......... - Auto
DIMM3 Clock Fine Delay.............. - Current[2066ps]
DIMM4 Clock Fine Delay.............. - Current[2066ps]
Ch2 Control0 Fine Delay............. - Current[48ps]
Ch2 Control1 Fine Delay............. - Current[48ps]
Ch2 Control2 Fine Delay............. - Current[48ps]
Ch2 Control3 Fine Delay............. - Current[48ps]
Ch2 Command Fine Delay.............. - Current[394ps]

Ch1 Ch2 Common Clock Setting........ - Auto

Ch1 RDCAS GNT-Chip Delay............ - Auto
Ch1 WRCAS GNT-Chip Delay............ - Auto
Ch1 Command To CS Delay............. - Auto
.
Ch2 RDCAS GNT-Chip Delay............ - Auto
Ch2 WRCAS GNT-Chip Delay............ - Auto
Ch2 Command To CS Delay............. - Auto

Flex Memory Mode..................... - Auto
CAS Latency Time (tCL)............... - 5
RAS# to CAS# Delay (tRCD)............ - 5
RAS# Precharge (tRP)................. - 5
Precharge Delay (tRAS)............... - 15
All Precharge to Act................. - auto
REF to ACT Delay (tRFC).............. -52
Performance Level.................... - 10

Read delay phase adjust Press Enter:

Channel 1 Phase 0 Pull-In........... - Auto
Channel 1 Phase 1 Pull-In........... - Auto
Channel 1 Phase 2 Pull-In........... - Auto
Channel 1 Phase 3 Pull-In........... - Auto
Channel 1 Phase 4 Pull-In........... - Auto

Channel 2 Phase 0 Pull-In........... - Auto
Channel 2 Phase 1 Pull-In........... - Auto
Channel 2 Phase 2 Pull-In........... - Auto
Channel 2 Phase 3 Pull-In........... - Auto
Channel 2 Phase 4 Pull-In........... - Auto

Write to PRE Delay (tWR)............ - auto
Rank Write to Read (tWTR)........... - auto
ACT to ACT Delay (tRRD)............. - 4
Read to Write Delay (tRDWR)......... - 9
Ranks Write to Write (tWRWR)........ - Auto
Ranks Read to Read (tRDRD).......... - Auto
Ranks Write to Read (tWRRD)......... - Auto
ALL PRE to Refresh.................. - Auto

Voltage Settings:

CPU VID Control..................... - 1.55V
CPU VID Special Add................. - disable
CPU VID Special Add................. - 0.147%
DRAM Voltage Control................ - 2.27v
SB Core/CPU PLL Voltage............. - 1.75v
NB Core Voltage..................... - 1.455v
CPU VTT Voltage..................... - 1.367v
Vcore Droop Control................. - Enabled
Clockgen Voltage Control............ - 3.60v
GTL+ Buffer Strength................ - Strong
CPU GTL 0 REF Volt.................. - 0.6125
CPU GTL 2 REF Volt.................. - 0.6125
CPU GTL 1 REF Volt.................. - 0.6125
CPU GTL 3 REF Volt.................. - 0.6125
North Bridge GTL 0 REF Volt......... - 0.6050
North Bridge GTL 1 REF Volt......... - 0.6050
FSB Vref............................ - 00
 
Genie BIOS Settings:
 
Exist Setup Shutdown................ - Mode 2
Exist Shutdown After AC loss........ - Enabled
AC Shutdown Free.................... - Enabled
O.C Clock Fail Retry Counter........ - 0
O.C Clock Fail CMOS Reloaded........ - Disabled
CPU Clock Ratio..................... - 7.5
CPU N/2 Ratio....................... - Enable
Target CPU Clock.................... - 4500MHz
CPU Clock........................... - 600
Boot Up Clock....................... - Auto
CPU Clock Amplitude................. - 900mV
CPU Clock0 Skew..................... - 200ps
CPU Clock1 Skew..................... - 0ps
DRAM Speed.......................... - 333/667
Target DRAM Speed................... - 1201MHz
PCIE Clock.......................... - 100mhz
PCIE Slot Config.................... - 1x 1x 
CPU Spread Spectrum................. - Disabled
PCIE Spread Spectrum................ - Disabled

[ahoey_amj]

Tweet

Nah bro.,... Ada yang mo sharing nih ilmunya... Mari diterapkan....
Btw..., Kira2 kalo diterapkan ke DK x48-T2RSB+ bisa ga yah...??
Mo Coba2 nih... Let's we Trial & Error Mode = Clear CMOS..

[cyber_shinigami]

Tweet

Waduh TQ banget neh bro masukan nya akhirnya DK LP 45 T2RS + Gw bisa masuk di 4.00 dengan 400 x multiplier 8 divider 1:1 RAM lari di 2 x 500 cuma di test di Prime 95 langsung merah stoped cuma di pake browsing buka ini itu gak masalah seh ummm dan akhirnya restart juga :-D, ada saran bro untuk settingan yg lebih pass buat gw soalnya kan settingan bro lebih tinggi? kali ja beda dengan seri UT
ato Volt nya bisa diturunin dikit ngeri eh Vcore di 1.55 , emang seh idle 40 derajat gak tau neh poll nya berapa ? biasanya seh bisa nginjek 60 derajat ?

Edit
sekarang gw jalanin di 3,6 dengan fsb x multi 450 x 8 VCORE 1,440 dengan divider 4:5 di 563 VRAM 2,23
cuma di test di prime 95 maseh eror apa yg salah ya